Latest release
Changes since previous release:
- Updated Mill-Turn control layer: Fixed Unmatched Conditionals warning for 2025
- Updated Okuma Renishaw Calibration Cycles
- Updated Renishaw Lathe ProbeOn/ProbeOff
- Added Heidenhain 444 Cycle Probing 3D
- Added Siemens Detection Cycles
- Added Point 3D to Cycle Builder
- Added linked value option to Cycle Builder
- Fixed issue with Siemens Rectangle at angle cycle when using custom WCS
- Fixed Mill-Turn linked point now regenerated if missing
- Fixed issue Mastercam Exit event when using Cycle Builder
Previous releases
Changes since previous release:
- Added CIMCO Inspect for Mastercam 2024 and 2025
- Renishaw 3D Point surface probing
- Option to configure rapid pre position move for Siemens
- Fixed issue with suppress probe on/off
- MT updated optional inputs for Renishaw from int to real
Changes since previous release:
- Added Renishaw Tool Setter Cycle Support
- Added Renishaw Feature To Feature optional inputs
- Added option to configure custom controls and extensions using XML editor
- Added Siemens Calibration cycles
- Fix issue with Makino datum cycles
Changes since previous release:
- Added Custom Log Editor
- Official release of Probing for Mastercam 2025
Changes since previous release:
- Updated Mill-Turn control layer
Changes since previous release:
- Updated Mill-Turn control layer
- Updated cycle previewer display
- Updated Renishaw contour cycle. Now works with different toolplanes
- Fixed issue with preposition for siemens edge one axis cycle
Changes since previous release:
- Fixed issue when loading old probing operations after upgrading the program to a new version of Mastercam.
Changes since previous release:
- Fixed an issue with the probing modifier.
- Added a cycle previewer. A preview of the cycle output can be viewed while configuring.
- Updated Renishaw Detection cycles. Removed redundant prepositions and detection lines.
Changes since previous release:
- Official release of probing for MILL-TURN.
- Fixed an issue with operation selection in Mastercam when using other Chooks than Probing.
Changes since previous release:
- Fixed issue with measurement result output for MILL-TURN
Changes since previous release:
- MILL-TURN support has been added to Cimco Probing. Please contact us for additional information and setup instructions
- Fixed a memory issue that could result in Mastercam crashing when creating a new operation.
- Added probing for Mastercam 2025
- Added an axis combination menu option for Mill. If machine configuration contains multiple axis combinations, these can now be selected for a probing operation.
Changes since previous release:
- Added missing feedrates to Siemens preposition moves
- Added GoTo options for Renishaw cycles
- Added If/then conditions to Renishaw detection cycles
Changes since previous release:
- Adjusted Renishaw Lathe cycles
Changes since previous release:
- Fixed an issue with geometry from stock selection when using custom WCS
Changes since previous release:
- Fixed incorrect probing mics values text displayed in menu
- Fixed Siemens Groove cycle selection
- Updated translation files, removed unicode characters
Changes since previous release:
- Fixed a translation issue, that blocked posting in mastercam for some cycles
- Updated translation files
- Added support for Millplus controls
Changes since previous release:
- Added Roeders test cycles
- Changed condition check for moves and manual entries in custom cycle builder
Changes since previous release:
- Changed Siemens rectangle cycle geometry selection, can now select geometry at an angle
- Adjusted the Siemens corner cycles toolpath and post output
- Added missing pre position moves to siemens cycles
- Added custom tool number override to renishaw
- Added measurement results to Renishaw detection cycles
- Move measurement results post output to after if/then conditions for Renishaw
- Added Angled surface cycle to Renishaw
- Removed geometry selection when closing probing operation
Changes since previous release:
- Installer updated, valid mastercam versions will now always be selected as default
- Fix issue when loading default parameter values
Changes since previous release:
- Probing license check removed when posting in mastercam
Changes since previous release:
- Fix an issue with Siemens Datum Cycles. Correction Type parameter now correctly outputted
Changes since previous release:
- Fix an issue with Renishaw detection cycles output coordinates calculation
Changes since previous release:
- Fix an issue with Geometry not being saved in Cimco Probing level
Changes since previous release:
- Updated Cimco Probing tutorial files
- Added Tool option to installer(Renishaw Probes)
- Fixed image display error on multi monitor screen layout
Changes since previous release:
- Added diagrams and tooltips to Siemens, Blum, Okuma, Heidenhain and Makino
- Fix output issues for Renishaw Lahte
- Added more geometry selection options for lathe
- Added more toolplane options for circlepair geometry selection
Changes since previous release:
- Added Renishaw Calibration Cycles
- Fixed surface point cycle issue, when using custom tool plane and wcs in mastercam
Changes since previous release:
- Added feature to feature measuring option to Blum point one axis cycle
- Added new probe detection category to Renishaw
- Added clear and select all option to save default parameters
- Added expired maintenance display message
Changes since previous release:
- Added Re-Machining Variable Override for Renishaw
- Heidenhain iTNC 530 V2005 TCH 401 removed invalid params
- Fix an issue with Xml post updated method. Cimco probing xml section can now be passed elsewhere in the post when using the Xml Post Configuration Editor
- Mastercam Manual Entry comment and code now displayed in Remachining list
- Automatic tool plane selection user setting override removed when upgrading versions
Changes since previous release:
- Added wireframe point indication when selecting geometry
- Fixed an issue that resulted in incorrect rotation calculations and rounding errors in MIll posts
- Fixed an issue that resulted in mastercam crashing, when selecting geometry and using the scrollwheel or scrollbar
Changes since previous release:
- Added Cimco Probing About Section
- Added support for PENTA MACHINE PROBING - Kinetic Control
- Added Option for changing the _TZL and _TDIF param for Siemens Cycles
Changes since previous release:
- Beta Release Of Renishaw Lathe supporting the following controls
- Mazak
- Fanuc
- Doosan
- Haas
- Okuma
- Fixed an issue with Heidenhain 404 cycle
- Fixed an issue with DMG Mori Point One Axis Cycle
- Added Probe suppressing On/Off for DMG Mori cycles
Changes since previous release:
- Fixed an issue with Heidenhain Q305 param, that caused Mastercam to crash
- Added G110-G129 Offset support for Haas Renishaw
- Made Pre Alignment Axis Param Optional for Renishaw alignment Cycles
Changes since previous release:
- Added support for Mastercam 2024
- Cimco Probing will now automatically be added to Ribbor bar
Changes since previous release:
- Added Geometry/Cycle information to geometry list
- Added operation name and correct mastercam placement id to operations in validation(Scrap/Re-Machining/Tolerance)
- Added option for using the Reporter W1.1 and W2.1 for the Renishaw Dprnt parameter
- Added additional input options to Renishaw Alignment and Datum cycles
- Fix an issue with Renishaw Point At Angle cycle
- Fix an issue with Doosan Renishaw cycles 9843, 9817 and 9818
Changes since previous release:
- Fixed an issue with the feature to feature mode, that caused Mastercam to crash
- Fixed an issue with the Cycle images being display on the wrong screen, when selecting a new cycle in the Menu
Changes since previous release:
- Added new Cimco Probing Xml configuration extention
- This extention can be added to you Cimco Ribbarbar
- The Xml configuration extention allow you to edit and change to you Cimco Probing Xml settings directly from Mastercam
- Added Renishaw 9818 K cycle
- Added more Workoffset options to Okuma
- Removed redundant Z move for Renishaw cyles 4th Axis X & Y Measurement in nc output
- Fixed an issue, when opening a probing cycle created using different Probing xml settings, would couse mastercam to crash
- Fixed an issue with Heidenhain parameter Q330 and Qs330
Changes since previous release:
- Fixed an issue where invalid saved default cycle settings where used
Changes since previous release:
- Heidenhain cycle parameter Q305 changed to string input
- Heidenhain cycle 403 select geometry method updated. Correct measuring axis will now be selected
- Fixed Datum cycle selecting crash
Changes since previous release:
- Probing Modify Tool Plane Matrix Calculation Updated
Changes since previous release:
- Updated the select from stock option.
- Updated Surface Probing.
- Added wireframe geometry highlighting.
- Fixed an issue for G320 cycle output.
- Fixed an issue for Blum Datum cycles.
- Fixed an issue for Siemens IF/Then conditions upper and lower tolerance.
Changes since previous release:
- Removed Educational license check.
Changes since previous release:
- Added pictures and decription for Renishaw cycles and parameters.
- Fixed an issue for older version of Siemens control where Active WO would come out wrong.
- Removed unsupported input for Renishaw cycles.
- Added option to change WCS.
- Fixed an issue for toolplane selection for Renishaw.
- Fixed an issue for Heidenhain when not using top/bottom WCS.
- Fixed an output issue for Okuma.
- Added Manual Entry option for If/Then conditions for all cycles.
Changes since previous release:
- Added new Haas dprint option.
- Added additional features to Okuma_Renishaw O9818.
- Fixed translation for new Heidenhain cycles.
- Added highlight when selection solid geometry.
- Added option to supress probe on/off calls between probing operations.
- Improved save default function.
- Fixed checkboxes for output to not output if deselected.
- Fixed scrollwheel/scrollbar for probing operations.
- Added option to bundle edit cycle parameters.
Changes since previous release:
- Added new heidenhain cycles for TNC640. 1410, 1411, 1420.
- Fixed calculation issue for probing_modify 11004:
- Fixed Mazak WPC & Extended workoffset numbers.
- Add option to Suppress I & J commands on 9815/9816 cycles.
- Add input letters to cycle name for Renishaw.
Changes since previous release:
- Fixed work offset output for Mazak.
- Updated maximum tool offset number value. Added automatic tool offset number setting for makino.
Changes since previous release:
- Fixed an issue with 2 points one line missing output for Renishaw
Changes since previous release:
- Fixed a bug with single seat license for Mastercam 2023
Changes since previous release:
- Fixed a bug with multiple machine groups in Mastercam 2023
- Fixed bug where solid selection would create geometry in Mastercam 2023
Changes since previous release:
- Added support for Mastercam 2023
- Fixed various issues for Makino
Changes since previous release:
- Added additional support for Renishaw
Changes since previous release:
- Improved stability and various bug fixes.
Changes since previous release:
- Added Tool compensation for Makino cycles.
Changes since previous release:
- Added Measureresult output to Makino
Changes since previous release:
- Fixed crash issue with Makino inspection cycles
Changes since previous release:
- Fixed a bug where two point one axis for renishaw would not generate
- Fixed a bug with width calculation
Changes since previous release:
- Fixed makino work offset releated output
Changes since previous release:
- Fixed issue with missing restart level for probing operations
- Fixed issue with TooltipCenter Makino
- Now setting datum with G10 Makino
- Changed point to use P9728 Makino
- Added additional functionality to point and rectangle Makino
- Fixed an issue with swapping probing settings within the post
Changes since previous release:
- Fixed an bug causing mastercam to crash when importing probing operations
- Added better support for 4k resolution
Changes since previous release:
- Added MacroVersion to XML section for Renishaw
- Fixed an bug with toolpath for 4th axis Renishaw
- Corrected R output for Renishaw cycles
- Corrected Corner inside start coordinates for Renishaw
- Corrected Corner backplot to work as stated in Renishaw documentation
- Changed IF/THEN to use H value instead of V for Renishaw v2018 and later
Changes since previous release:
- Added IF/THEN for Mikano
- Added Tooltipcenter for Mikano
Changes since previous release:
- Fixed Z output in 3D Corner for Blum
Changes since previous release:
- Added missing NCG variables for IF/THEN in Haas_Renishaw
Changes since previous release:
- Fixed an issue where measure result would not output variables for blum
Changes since previous release:
- Added support for Haas NGC variables
Changes since previous release:
- Fixed issue with cornor for blum
- Added support for tooltipcenter for blum
- Fixed issue with saftey distance for blum
Changes since previous release:
- Fixed issue with width calculation for ridge cycles
Changes since previous release:
- Added proper calculation of ridge width
- Corrections for older Siemens measure plane output
Changes since previous release:
- Corrected validation variable for Renishaw measure width cycle
- Added _ID parameter to older Siemens cycle 998 measure plane output
- Fixed issue with some post XML settings being reset
Changes since previous release:
- Corrected cycles number for Renishaw external corner cycle
- Corrections for Brother Renishaw cycle numbers
- Corrections for Fanuc DMG Mori output
- Replaced work offset parameter (S) from Renishaw 4th axis alignment cycle with G10 work offset setting
- Added post xml option tp specify value type for tool correction parameter in Siemens cycles
- <ToolCallType>Number</ToolCallType>
- <ToolCallType>Name</ToolCallType>
- <ToolCallType>NumberAsName</ToolCallType>
- Added post xml option to disable probe on/off output by using empty ProbeOn/ProbeOff elements
- Added post xml option to override tool tip compensation point
- <ToolTipCenter>Yes</ToolTipCenter>
- <ToolTipCenter>No</ToolTipCenter>
- Added Czech translation
- Added chook version to installer name
Changes since previous release:
- Enabled surface probing for Makino
- Removed _ID and added _SETV[2] and _SETV[3] for older Siemens measure plane output
- Fixed issue with long operation names causing crash
Changes since previous release:
- Fixed issue with wrong value type for Heidenhain parameter Q311
Changes since previous release:
- Fixed issue with modify_tool_plane_origin_local
Changes since previous release:
- Fixed issue with loading legacy Siemens measure plane cycle parameters
- Added missing K argument for Mazak Renishaw measure 4th axis
- Added missing _STA1 output for older Siemens cycle 977
Changes since previous release:
- Fixed issue with validation not sometimes not being processed correctly during output
Changes since previous release:
- Added VCRedist 2012 x64 to the installer
- Added support for Mastercam 2022 beta
Changes since previous release:
- Adjusted title on license warnings
- Added translation for measurement result comment output
- Corrected toolpath for Siemens measure plane cycle
- Added option to use tool number for tool adjustment in Siemens cycles, using the post xml setting ToolCallByName Yes/No
- Added feedrate to G31 moves for Fanuc DMG Mori cycle
- Correction for Fanuc DMG Mori datum setpoint output
Changes since previous release:
- Fixed issue with incorrect dimension and center for rectangle from chain
- Added cycle numbers to Renishaw cycle names
Changes since previous release:
- Fixed issue with measuring height in point measurement for Makino, Renishaw and DMG Mori
- Changed plane match policy for surface probing in the Z-axis direction
Changes since previous release:
- Displaying clients using licenses in case of no floating licenses available
- Added DMG Mori cycles for Fanuc
Changes since previous release:
- Fixed issue with Software Manager being installed in wrong directory
- Fixed issue with probing output being initialized when no probing operation was selected for posting
Changes since previous release:
- Fixed issue with first/second measurement point from geometry for Heidenhain cycle 426
Changes since previous release:
- Removed W0. from Renishaw measure width cycle
- Included .Net Framework and Visual C++ Redistributables in Software Manager installer